Test report
Matching the eccentric shafts:
- Matching angle cylinders 1 - 4: <#abgleichwinkel_zyl_1_4#> degrees
- Matching angle cylinders 5 - 8: <#abgleichwinkel_zyl_5_8#> degrees
Compression check at minimum lift:
- Date and time: <#datummin#><#zeitmin#>
- Speeds during the measurement (start, end and mean): <#adrzmin#>, <#edrzmin#>, <#mdrzmin#> rpm
- Measurement OK/nOK: <#status_messung_min#>
Cylinder |
Pressure [bar] |
|---|---|
1 |
<#zmin1#> |
2 |
<#zmin2#> |
3 |
<#zmin3#> |
4 |
<#zmin4#> |
5 |
<#zmin5#> |
6 |
<#zmin6#> |
7 |
<#zmin7#> |
8 |
<#zmin8#> |
During the compression check, the calibration of the eccentric shafts is switched off. This is why the two cylinder banks have to be examined separately.
- Mean value of compressions for cylinders 1-4: <#mwmin1#>
- Mean value of compressions for cylinders 5-8: <#mwmin2#>
Compression check at maximum lift:
- Date and time: <#datummax#><#zeitmax#>
- Speeds during the measurement (start, end and mean): <#adrzmax#>, <#edrzmax#>, <#mdrzmax#> rpm
- Measurement OK/nOK: <#status_messung_max#>
Cylinder |
Pressure [bar] |
|---|---|
1 |
<#zmax1#> |
2 |
<#zmax2#> |
3 |
<#zmax3#> |
4 |
<#zmax4#> |
5 |
<#zmax5#> |
6 |
<#zmax6#> |
7 |
<#zmax7#> |
8 |
<#zmax8#> |
- Maximum deviation cyl. 1-8: <#deltamax#>
<#ergebnis_komp_pruefung#>
Smooth-running values:
- Temperature at the radiator outlet at start of measurement: <#tka_beginn1#> °C
- Engine temperature at start of measurement: <#tmot_beginn1#> °C
- Nominal speed during measurement: <#solldrehzahl#> +/- <#toleranz#> rpm
- Actual speed during measurement: <#durchschnitt_drehzahl#> rpm
Cylinder |
Standard deviation |
Mean value |
|---|---|---|
1 |
<#sa_zyl_1#> |
<#mw_zyl_1#> |
2 |
<#sa_zyl_2#> |
<#mw_zyl_2#> |
3 |
<#sa_zyl_3#> |
<#mw_zyl_3#> |
4 |
<#sa_zyl_4#> |
<#mw_zyl_4#> |
5 |
<#sa_zyl_5#> |
<#mw_zyl_5#> |
6 |
<#sa_zyl_6#> |
<#mw_zyl_6#> |
7 |
<#sa_zyl_7#> |
<#mw_zyl_7#> |
8 |
<#sa_zyl_8#> |
<#mw_zyl_8#> |
- Standard deviation:
If the standard deviation is greater than 0.15, the measurement is invalid. - Mean value:
The smooth-running values indicate whether a cylinder accelerates or decelerates the crankshaft during its operating cycle. A negative value indicates an accelerating cylinder, while a positive value indicates a decelerating cylinder.