ABS/ASC 5
The ABS/ASC 5 system is a further development of the ABS/ASC and ABS/ASC+T systems as already used for a long time on series E32 and E34 vehicles.
The ABS/ASC 5 system comprises the functions ABS and ASC+T. ABS stands for antilock brake system, ASC+T for automatic stability control + traction.
The antilock brake system (ABS) prevents the wheels locking even in the case of a full emergency brake on a slippery road surface, thus considerably increasing the driving stability and steerability of the vehicle.
The automatic stability control + traction (ASC+T) is in effect a reverse of the ABS system. It prevents the drive wheels from slipping during acceleration and therefore also increases the driving stability and traction of the vehicle.
Voltage supply ABS/ASC control unit
The ABS/ASC control unit is ready for operation as of ignition lock position 2. The positive supply takes place via the DME main relay. The positive supply is retained for approx. 5 - 20 seconds after switching off the ignition (DME retention circuit).
The negative supply is provided via three ground lines.
Speed signals
Input signals
The wheel speed signals are made available by four "active" speed sensors.
These active speed sensors operate in accordance with the Hall principle, in which changes in the magnetic field strength produce alternating voltages with the frequency used as a measure for the wheel speed. In contrast to the passive speed sensors, the actual sensor element and electronics for signal conditioning are integrated in the active speed sensors.
Advantages of active sensors:
- Speed sensing down to almost 0 km/h
- Signal amplitude independent of speed
- Compact size, low weight
- Installation directly in wheel bearing possible
- Simple sensor monitoring
The speed signals are square-wave signals with constant amplitude (low level = 0.75 V, high level = 2.5 V), frequencies within the range from 0 to approx. 1700 Hz are obtained for the speed range from 0 ... 250 km/h dependent on the tire circumference.
The ABS/ASC control unit provides the voltage supply to the active sensors (7.6 ... 8.4 V direct voltage).
Output Signals
Since other control units also require the wheel speeds, such as the instrument cluster electronics (IKE) or electronic damper control (EDC), the speed signals are processed accordingly in the ABS/ASC control unit.
These speed output signals are square-wave signals with constant amplitude (low-level < 1 V, high-level> 11 V). The frequency is dependent on the wheel speeds and lies in the range between 0 - 1700 Hz (0 - 250 km/h).
Hydraulic unit
The hydraulic unit consists of solenoid valves, a two-circuit return pump and an accumulator chamber per brake circuit.
Solenoid valves
The solenoid valves are switched by the ABS/ASC control unit. Depending on the switching status, they connect the wheel brake cylinders with the corresponding circuit of the master brake cylinder or of the return pump or close the wheel brake cylinder with respect to both.
Two solenoid valves, one inlet and one outlet valve, are necessary for each of the four control circuits. An additional intake valve and a changeover valve are necessary for ASC control. The intake valve facilitates the pressure build-up via the self-priming pump element in the return pump. The changeover valve prevents the brake fluid flowing back into the supply reservoir during control cycles.
The solenoid valves are powered by the valve relay as of ignition lock position 2. The valve relay is activated by the ABS/ASC control unit.
Return pump
The return pump is activated only during ABS or ASC control. It pumps the brake fluid, flowing from the wheel brake cylinders when the pressure is reduced, via the corresponding accumulator back into the relevant circuit of the master brake cylinder. The return pump is switched on and off by the engine relay, controlled by the ABS/ASC control unit.
Accumulators
The accumulators in the hydraulic unit serve the purpose of temporarily taking up the brake fluid which accumulates suddenly during pressure reduction.
Indicator lamps
ABS/ASC system faults or system statuses are indicated in the instrument cluster with the aid of the ABS safety lamp and the multifunction lamp.
The ABS/ASC system is switched on automatically and then ready for operation every time the ignition is switched on. If the entire system is free of faults, both the ABS safety lamp as well as the multifunction lamp go out after approx. 2 seconds (lamp check).
If the safety circuit detects a fault in the subsystem ABS, the entire system, i.e. ABS and ASC, is switched off (ABS safety lamp and multifunction lamp light up). If the fault no longer occurs during the next starting procedure both lamps go out again after the lamp check.
If the safety circuit detects a fault in the subsystem ASC, either the entire system or the subsystem ASC is switched off depending on the type of fault (ABS safety lamp and/or multifunction lamp light up).
The ASC subsystem can be switched off with the ASC passive button under special driving conditions (e.g. driving off in deep snow). This is indicated by a steady light in the multifunction lamp.
The driver's attention is drawn to an ASC control function by the ASC multifunction lamp flashing while driving (frequency 3 Hz).
Note
During diagnosis (communication with the diagnosis and information system), the ABS safety lamp and the multifunction lamp light constantly.
Switches and push-buttons
Brake light switch
The brake light switch informs the ABS/ASC control unit of when the brake pedal is operated. This results in immediate termination of any brake intervention during an ASC control function thus improving the control comfort.
Note
Faults in the brake light switch circuit are stored in the defect code memory, however, the ABS safety lamp does not light up in this case.
Handbrake switch
The handbrake switch informs the ABS/ASC control unit that the handbrake is applied. This results in an increase in the threshold for the engine drag torque control (MSR) thus improving the control comfort.
ASC passive button
The ASC subsystem can be switched off with the ASC passive button under special driving conditions (e.g. driving off in deep snow). This is indicated by a steady light in the multifunction lamp. The ABS subsystem remains operable without restriction.
The ASC system is reactivated after pressing the button once again.
Control concept
ABS Control
During the ABS control procedure, the front wheels are controlled individually while the rear wheels are controlled together. An ABS control cycle consists of the three phases: Pressure retention, pressure reduction and pressure build-up.
If a speed sensor signals strong wheel deceleration, i.e. a tendency to lock, initially the brake pressure of this wheel is not increased, i.e. the pressure is retained at the level previously reached.
If the wheel deceleration continues to increase, the brake pressure is reduced so that the wheel is braked to a lesser extent.
The wheel rotates faster again due to the reduced brake pressure. The pressure is increased again when a certain speed limit is reached. Rotation of the wheel is slowed down again by this increase in pressure.
Depending on the condition of the road surface, approx. 5 to 12 control cycles take place per second. The return pump is permanently activated during the control procedure.
With no power applied, the inlet valves are open in their rest position while the outlet valves are closed in their rest position:
Pressure phase |
Solenoid valve / status |
|---|---|
Pressure retention |
Inlet valve / closed (power applied) |
|
Outlet valve / closed (no power applied) |
Pressure reduction |
Inlet valve / closed (power applied) |
|
Outlet valve / opened (power applied) |
Pressure build-up |
Inlet valve / opened (no power applied) |
|
Outlet valve / closed (no power applied) |
ASC control
ASC reduces the high torques at the drive wheels by correspondingly influencing the engine management and by braking the drive wheels.
This is achieved by following control interventions:
- Reduction in choke position:
The choke adjustment represents the first stage of engine intervention. In this system, the ABS/ASC control unit activates a throttle actuator which is driven by an electric motor and which adjusts the choke in the direction of a smaller throttle opening by means of an operating (Bowden) cable. The throttle actuator is activated by clocking the positive and negative supply.
The current position of the choke is detected by a throttle potentiometer and signaled back to the ABS/ASC control unit. - Ignition timing in "retard" direction
Ignition timing adjustment is a supplement to the relatively slow reduction in the choke position. The ignition intervention is controlled by means of the digital motor electronics. Ignition timing adjustment represents a fast yet smoother engine torque reduction than blanking out ignition and injection pulses. - Blanking out of ignition and injection pulses
Blanking out the ignition serves the purpose of quickly reducing the drive slip. The delay time up to blanking out and therefore to reducing the engine torque is very short. Blanking out the injection which is activated simultaneously prevents uncombusted mixture entering the exhaust system in the case of the ignition signals being blanked out over a longer period of time. Blanking out of the ignition and injection pulses is also controlled by the digital motor electronics. - Brake intervention at drive wheels:
Brake intervention at the drive wheels takes place analogously to the ABS control based on the three control phases: Pressure build-up, pressure retention and pressure reduction. The pressure for brake intervention during an ASC control phase is applied directly via the intake valve and the self-priming pump element to the corresponding wheel brake. The changeover valve prevents the brake fluid flowing back into the supply reservoir during control cycles.
The automatic transmission control is also influenced.
Interfaces
The most important interfaces of the ABS/ASC control unit are those for the choke, digital engine electronics (DME), adaptive transmission control (AGS) and for the alternator:
Choke
The ABS/ASC control unit reduces or increases the torque at the drive axle by closing or opening the choke accordingly. This intervention is the first but relatively slow measure in reducing the drive torque during ASC control.
Digital Motor Electronics (DME)
The ABS/ASC control unit can implement the following engine interventions by way of the digital engine electronics:
Intervention |
Effect |
|---|---|
Ignition timing set towards "retard" |
Fast yet smooth reduction of drive torque |
Blanking out ignition/injection pulses |
Fast reduction of drive torque |
Increase in idle speed |
Reduction in engine drag torque on vehicles with manual transmission |
Adaptive Transmission Control (AGS)
Vehicles equipped with an adaptive transmission control (AGS) can receive a signal from the ABS/ASC control unit during an ASC control phase, i.e. mainly on road surfaces with snow and ice, to the effect that imminent gearshifts, resulting in an increase in the torque in the drive axle are suppressed.
Alternator
The alternator signal terminal 61 is a redundant signal and serves the purpose of detecting whether the engine is running. At an alternator voltage below 8 V, the ASC subsystem switches off and the multi-function lamp lights up. However, no fault is stored in the defect code memory.