WDSBMW wiring diagrams
← Back

Single-axle self-levelling suspension

Single-axle self-levelling suspension

The single-axle self-levelling suspension has the task of keeping the vehicle height at the rear axle at the specified nominal height setting independently of the load status.

Brief description of components

The single-axle self-levelling suspension consists essentially of the following components:

GR_FB3707002

The pneumatic plan is simplified.

Index

Explanation

Index

Explanation

1

Air supply system

2

Air cleaner

3

Ventilation line

4

Drain valve with pressure retention and pressure limitation function

5

Compressor with attachment parts

6

Electrical control valve

7

Solenoid valve block

8

Solenoid valve for control of the air springs

9

Air spring

10

Air spring

11

Solenoid valve for control of the air springs

12

Restrictor

13

Air drier

14

Compressor

15

Electric motor

 

 

System functions

The self-levelling suspension works by feeding or extracting air into or out of the air springs.

The height sensors provide the EHC control module with information on the heights of the left-hand and right-hand sides of the vehicle.
If the heights are outside the specified tolerance, the system intervenes using the air supply unit to set the nominal ride-level height.

GR_FB3707001

Index

Explanation

Index

Explanation

1

EHC control module

2

Air supply system

3

Solenoid valve block

4

Solenoid valve for control of the air springs

5

Solenoid valve for control of the air springs

6

Compressor with attachment parts

7

Electrical control valve

8

Electric motor

9

Compressor relay

10

Height-level sensor

11

Height-level sensor

K CAN

Body CAN

Terminal 30

Terminal 30

Terminal 30g

Terminal 30 switched

Changes to the load mainly take place when the vehicle is at a standstill, before or after a journey. In order to load the vehicle, the doors or boot/rear hatch have to be opened. The system is activated when a door or the luggage compartment lid is opened. The system only switches off 20 minutes after the driver leaves the vehicle (consumer unit shutdown signal).

In order to distinguish load changes from disturbances such as uneven roads, the signals of the height-level sensors are filtered. To ensure use in line with requirements, for each signal two filtered signals with different frequencies are calculated (low-pass filtering with fast and slow filtering).
During an adjustment, it is always the fast filtering that is used. This prevents an increase in the adjusted height above the target value.
The slow filtering is used while the vehicle is being driven. This type of filtering means that vibrations produced by the road surface are filtered out.

Both sides of the vehicle are adjusted individually. This means that the target/actual comparison is also run for both sides individually. (exception: Checking the minimum height in the Pre mode and in the control function ”transposition”. (In these control functions, the average values of the left-hand and right-hand side of the vehicle are analysed.)

The EHC control module uses the various signals and messages to detect the various driving states. Depending on the driving states, the adapted control functions are switched accordingly.

The following control functions of the single-axle self-levelling suspension are described:

Note: All of the following specified times and dimensions are examples.

The actual coding data depends on the model series and vehicle equipment.

Sleep mode

The Sleep mode is the initial state for interventions. In the Sleep mode, no intervention takes place. Adjustments that were started in other intervention modes are cancelled when the Sleep mode takes effect.

Pre mode

In the Pre mode (temporally controlled pre-run / after-run), loads are balanced out on getting into the car as well as for a certain time (approx. 20 minutes) after parking the vehicle.
The consumer unit shutdown signal is set by activities on the vehicle such as operating a door handle or the central locking system and output on the K-CAN.

In the case of ignition key position terminal R or terminal 15 or 'engine on' signal, the signal is set permanently.

If the vehicle is parked, the consumer unit shutdown signal remains set for approx. 20 minutes after the last action (e.g. door opening). If a door status changes within this 20 minutes, the after-run time is restarted. When this after-run time expires, the message 'switch off consumers' is sent and the control module switches for 1 minute into the Post mode before it goes into the Sleep mode.

In the Pre mode, the vehicle can only be raised to its specified height if the level drops significantly below the specified height. The tolerance range for the control is approx. 40 millimetres below the average value. (The tolerance range indicates when the electronics in the EHC control module make an adjustment.
This tolerance ensures that adjustments are only made in the event of large additional loads to increase ground clearance before driving away). Smaller payloads only lead to small amounts of spring travel which are only balanced out after the engine has been started. These characteristics reduce the load on the battery.
In the Pre mode, only the average value of the two signals of the height-level sensors are analysed.

Post mode (post adjustment)

The Post mode is used to balance out any inclination before entering the Sleep mode after completion of a journey. The control function has a time limit (approx. 1 minute).
In the Post mode, adjustment is made in a defined tolerance range (+7 / -10 millimetres).

Normal mode

The Normal mode refers to the normal operating condition of the vehicle. The Normal mode is initiated by means of the 'engine running' signal. Adjustment is made in a defined tolerance range per side (±10 millimetres, rapid filtering).

Drive mode

The Drive mode is activated in the EHC control module when a speed signal above 1 km/h is detected.
In the Drive mode, adjustment is made by means of slow filtering. In the Drive mode, e.g., different ride heights that occur as a result of the reduction in the vehicle mass due to fuel consumption are balanced out.

Cornering

The control function ”cornering” prevents adjustment when cornering is detected. The slow filtering is halted and any ongoing adjustment is cancelled.
The cornering is detected via the incoming lateral-acceleration signal (e.g. above 2 m/s2 cornering detected, below 1.4 m/s2 cornering completed). The DSC control module sends the lateral-acceleration signal via the K-CAN.

Transposition

The operating mode ”transposition” prevents balancing of any inclination when only one wheel of the vehicle drives over an obstacle. Balancing would lead to a renewed inclination of the vehicle after coming down from this obstacle and to a new adjustment.
If one wheel of a vehicle drives up onto the kerb and stops, the EHC control module switches from the Drive mode into the Normal mode. In this control function, the signals of the height-level sensors on the left and right are evaluated.
If the difference in height between the left-hand and right-hand side of the vehicle exceeds a certain value (e.g. 28 millimetres), a switch is made to the control function ”transposition”.

In this control function, the EHC control module analyses the car height in the centre of the axle.
If the vehicle is now loaded or unloaded, the value of the compression or rebound is analysed. If the value lies outside of the defined tolerance range (e.g. ±10 millimetres), an adjustment is initiated.
The left-hand and right-hand sides of the vehicle are raised or lowered in parallel. The difference in height between the two sides remains.
When the EHC control module goes into the Drive mode, the control function ”transposition” is terminated. Any ongoing adjustment is cancelled. The control function ”transposition” is terminated when the difference in height between the left-hand and right-hand sides of the vehicle falls short of a specified value.

Level up function (only E61 all wheel drive up to 09/2006)

The level up function is used to raise the vehicle rear end automatically after parking and leaving the vehicle.

The vehicle is raised automatically after parking as follows:

or

When the EHC control module goes into the Drive mode, the level up function is terminated. The vehicle is lowered to normal height.

Detection of an inclination after tyre pressure loss (only E70, E71 with 8-cylinder engine or optional extra 4UB ”3rd row seats”)

If the Run Flat Indicator (RPA) or Tyre Pressure Monitor (TPM) detects tyre pressure loss on one wheel, the control function reduces the load on the tyre concerned.

When the tyre pressure loss has been remedied and the Run Flat Indicator or Tyre Pressure Monitor no longer indicates tyre pressure loss, with the engine running this control function is terminated automatically after approx. 5 minutes.

Lifting platform

In the control function ”lifting platform”, adjustments due to wheel changes or work on the lifting platform are prevented.
The following conditions trigger the ”lifting platform” control function:

The height is stored in the EHC control module.
A reset is carried out when the vehicle returns to e.g. 10 millimetres below this stored height or the Drive mode is detected.

Transport mode

In the Transport mode, the nominal height is raised (e.g. 30 mm). Increasing the ground clearance ensures safe transport of the vehicle.

Production mode

The Production mode is used for assembly on the line and prevents regulating operations.

New EHC control module are delivered with the Production mode set. After assembly of the new EHC control module, the Production mode must be deleted.

Notes for Service department

General information

Performing ride-height-calibration

A ride-height-calibration must be performed after the following servicing operations:

For the ride-height-calibration, the measured vehicle height at the rear axle (actual height on the left and right) must be entered in the BMW diagnosis system. To do so, select the service function ”ride-height-calibration” on the BMW diagnosis system.
The actual height is measured between the lower edge of the rim flange and the wheel-house lower edge.

No liability can be accepted for printing or other faults. Subject to changes of a technical nature