WDSBMW wiring diagrams
← Back

Engine start engine start-stop

Engine start engine start-stop

The new function of automatic engine start-stop (MSA) is a fundamental component of the measures package to reduce CO2 emissions. The reduction in fuel consumption is achieved by automatic shutdown of the engine when the vehicle is at a standstill. The new start also takes place automatically as soon as the corresponding conditions required for switch-on are met.

The MSA will be deployed in the BMW 1 Series, 3 Series and MINI model series in conjunction with the manual transmission and four-cylinder engine.

Note! Bear in mind the designation used by marketing.

The marketing designation is automatic engine start-stop function.

MSA function, principle

The MSA ensures automated shutdown of the engine while the vehicle is being driven if the vehicle comes to a standstill and a number of essential vehicle conditions are met to enable this shutdown.

Examples (matrix, see chapter ”System functions”):

Just as automatic as this shutdown is the automatic restart of the engine as soon as the clutch is pressed again or there are other requirements.

Sample scenario: switching off the engine at a standstill at a red traffic light or in stop-and-go traffic.

GR_FB1306002

Index

Explanation

Index

Explanation

Index

Explanation

1

Vehicle moving

2

Gear is engaged.
The accelerator pedal is pressed.

3

The engine is running.
The time and temperature are displayed in the instrument cluster.

4

The driver brakes until the vehicle comes to a standstill.

5

The driver engages neutral and releases the clutch pedal.

6

The engine stops.
The symbol
”Start/Stop” lights up in the instrument cluster.

7

The driver wants to continue the journey.

8

The driver presses the clutch pedal.
The engine starts.

9

The gear can be engaged and the journey continued.
The symbol
”Start/Stop” goes out.


Important!

The automatic switch on of the engine on vehicles with MSA can also take place when the driver takes no action. Customer annoyance and customer complaints are not based on a malfunction! Situations in which the engine starts fully automatically without any action on the part of the driver are, for example:

Brief description of components

The MSA function is located in the engine electronics (DME or DDE). Various information from the bus systems is used for the MSA. New components are also necessary. The following components for the MSA are described:

Zero gear sensor

The zero gear sensor is mounted on top of the transmission case. The zero gear sensor detects the idle position of the gearstick.

GR_FB1308001

Index

Explanation

Index

Explanation

1

Zero gear sensor

2

Plug-in connection


Brake vacuum sensor

In order to ensure adequate brake power assistance in every situation, the brake booster is equipped with a partial vacuum sensor.
The brake partial vacuum sensor is located beside the brake booster and is connected via a separate cable.

GR_FB1308002

Index

Explanation

Index

Explanation

1

brake partial vacuum sensor

2

Plug-in connection


Important!

With a brake partial vacuum that is too low, the MSA also starts without activity on the part of the driver. Insufficient brake partial vacuum can lead to safety risks during braking manoeuvres, e.g. when rolling on an incline. To prevent this, the engine is started.

MSA button

The MSA button (MSA OFF) on the centre console switch cluster can be used to deactivate the MSA function. With each terminal change ”Terminal 15 On” or repeated pressing of the MSA button, the MSA is reactivated.

GR_FB1308007

Index

Explanation

Index

Explanation

1

MSA button

2

Center Console Switch Center


DC/DC converter

Due to the considerably more frequent occurrence of starting operations, the electrical load that occurs often leads to voltage dips in the vehicle network. In order to stabilize the power supply for certain voltage-sensitive electrical components, a DC/DC converter is used in conjunction with the MSA.
The DC/DC converter supplies the two relays ”terminal 30g_DC/DC” and ”terminal 30g-f_DC/DC” with a voltage that also remains constant during the starting operation.

GR_FB1308010

Index

Explanation

Index

Explanation

1

E-box

2

DC/DC converter

3

Plug-in connection

 

 

The DC/DC converter is fitted in the E-box in the engine compartment.

Via the test leads for input voltage and terminal 50, the electronics decide whether the power is supplied to the output via the bypass or the DC/DC converter.
In the bypass mode, the on-board supply voltage is not fed across the DC/DC converter, rather is transferred directly to the outputs. In the booster phase, the vehicle voltage is adapted.

AGM battery

In all cases, the MSA comes with the intelligent alternator control. The much more frequent charge and discharge cycles mean that the load on the battery is very high. The cycle resistance of AGM batteries means that they achieve similar results with regard to service life despite the high load.

GR_FB1308009

Important! Ensure an AGM battery is fitted.

In all cases, an AGM battery must be installed and registered in the vehicle for the MSA to work perfectly.

Clutch Switch

The present clutch switch is used as an input variable for the MSA to detect clutch operation.

GR_FB1308003

Index

Explanation

Index

Explanation

1

Clutch Switch

2

Plug-in connection


Bonnet contact switch

The bonnet contact switch is included as an influencing factor in the calculation of the MSA. If the engine bonnet is opened, the engine must not be started or stopped by the MSA for safety reasons.

GR_FB1308005

Index

Explanation

Index

Explanation

1

Bonnet contact switch

2

Electrical connection


Important!

In the event of a defective bonnet contact switch, the MSA function is suppressed.
If the bonnet contact switch is pulled upwards, the information ”Switch closed” is displayed. The MSA is active and an automatic engine start can take place.

Belt buckle switch (driver)

Via the belt buckle switch, the MSA can detect that the driver has fastened his or her seat belt. If the driver has not fastened his or her seat belt, the MSA reacts as follows:

GR_FB1308004

Index

Explanation

Index

Explanation

1

Seat belt buckle

2

Belt buckle switch


Alternator

The battery discharge during the engine shutdown by the MSA means that a more powerful alternator is installed.

GR_FB1308008


Starter motor

In conjunction with the MSA, the starter motor must do a great deal more work. The starter motor is therefore configured for a significantly higher number (approx. 8 times) of start cycles. The components of the starter motor have been adapted to the higher requirements.

GR_FB1308006


System functions

The following system functions for the MSA are described:

System circuit diagram

GR_FB1306001

Index

Explanation

Index

Explanation

1

brake partial vacuum sensor

2

Zero gear sensor

3

Engine management system (DME or DDE)

4

DC/DC converter

5

Input and output of the DC/DC converter to the distribution box

6

Distribution box (junction box)

7

Junction box electronics (JBE)

8

Intelligent battery sensor at the negative battery terminal

9

Centre console switch centre with MSA button

10

Integrated automatic heating and air conditioning system (IHKA)

11

Instrument cluster (KOMBI)

12

Clutch Switch

13

Bonnet contact switch

14

Car Access System (CAS)

15

Starter motor

 

 


Operating strategy: Enable or shutdown of the MSA

After every engine start, the function is automatically active and on stand-by. The MSA button (center console switching center) can be used to deactivate the function manually until the next terminal change. Pressing the button is confirmed by an LED lighting up.

During the diagnosis sessions, the MSA is temporarily disabled for safety reasons (this means until the next terminal change). This prevents the possibility of an automatic engine start during work in the engine compartment.
The status of a temporary shutdown can be read in the control-module functions at all times using ”Detection shutdown MSA”. Furthermore, the status of the non-detection of a vehicle with MSA can be read out in the control-module functions by means of ”Check installation of MSA” as well as ”Status coding MSA”.

Important! Pay attention to personal safety.

For reasons of personal safety, it must always be conscientiously determined that the engine start-stop function has been disabled before work in the engine compartment!

Shutdown request:

Condition

R55, R56

E8x, E9x

Only N43

Preparation for comfort stop

Driving speed less than 3 km/h

X

X

 

Engine speed under threshold

X

X

 

Minimum speed reached at least once

X

X

X

No gear is engaged

X

X

X

Clutch not pressed

X

X

 

Steering wheel not moved

 

X

 


Note! Definition of comfort stop.

Low filling during comfort stop prevents the engine from ”shaking”. The comfort stop function empties the intake air collector (engine runs for 1 second longer).

Shutdown inhibitor:

Condition

E8x, E9x, R55, R56

Only N43

Comfort stop

Shutdown inhibitor from operating strategy (cross locking)

X

X

Adaptation of shutdown inhibitor

X

X

Engine fault

X

X

Shutdown inhibitor from power management

X

X

Activated charcoal filter too heavily loaded

X

X

Brake vacuum too low

X

 

Catalytic converter temperature too low

Only N43

 

Engine temperature too low

X

X

Outside temperature outside the operating window

X

X

Little fuel in the fuel tank

Only N43

 

Time window closed (at least one shutdown inhibitor was active for too long during the stop attempt)

X

X

Diesel particle filter in regeneration

Only diesel

 

Conditions for comfort stop not met

Only N43

 

Shutdown inhibitor due to A/C-request signal

X

X

 

GR_FB1306003

Index

Explanation

1

The driver brakes until the vehicle comes to a standstill.

2

The driver engages neutral and releases the clutch pedal.

3

The engine continues to run. There is a shutdown inhibitor.


Switch-on request (simultaneously locks the preparation for comfort stop on the N43):

Condition

E8x, E9x, R55, R56

Clutch pressed more than 10 %

X

Vehicle starting to roll

X

Brake partial vacuum inadequate.

X

Switch-on request from power management

X

Switch-on request from A/C-request signal

X


Switch-on inhibitor:

Condition

E8x, E9x, R55, R56

No idling or clutch pedal not in end position

X

Engine just stopped (safety function to ensure safe engine runout. Otherwise, it can happen that the starter motor engages in the engine while it is still running out).

X


All conditions as well as general status information can be read out using the service function ”system check MSA”.

Reading out a history of the last stored shutdown inhibitors is possible by means of the service function ”read AV memory”. This enables a check of past customer complaints.

Display concept: Display in conjunction with the MSA

If the MSA has shut down the engine, a display appears in the instrument cluster.
The following symbol is shown in the LC display between the dials:

GR_FB1308011


There are also 2 Check Control messages available for the MSA.

GR_FB1306004

Index

Explanation

Index

Explanation

1

ID 397:

Automatic engine start/stop system failed!

2

ID 450:

Automatic engine start/stop system disabled!

 

Condition

Shutdown, fault has occurred

Temporary shutdown without indication

Temporary shutdown with indication

 

Check Control message:
ID 397

 

Check Control message:
ID 450

Fault in MSA cable

X

 

 

Fault in zero gear sensor

X

 

 

Fault 'zero gear position not yet learned'

X

 

 

Fault in brake partial vacuum sensor

X

 

 

Fault 'plausibility of zero gear sensor signal'

X

 

 

Clutch switch signal not plausible

X

 

 

CAN bus fault (relevant to MSA)

 

 

X

Radio remote control not within range or in the slot

 

 

X

Driver absent or engine bonnet open

 

 

X

Production mode active

 

X

 

Transport mode active

 

X

 

Workshop mode active

 

X

 

MSA temporarily disabled via BMW diagnosis system

 

X

 

Engine fault that is severe for MSA

 

 

X

Starting operation cancelled by CAS (protection of the starter motor)

 

 

X

Tow-starting detected

 

X

 

MSA disabled via MSA button

 

X

 

Engine not yet started after ignition ON

 

X

 

A Check Control message appears if a system fault (with or without necessary component replacement) is active or the MSA is disabled.

Corresponding reading options are available through the service functions ”system check MSA” as well as ”read AV memory”.

Other service functions serve as additional plausibility checks and checks of the function characteristics (exception: learn / write zero gear sensor).

Power management

The battery status that is calculated in the Advanced Power Management (APM) is a major influencing factor on the MSA. The aim is to enable a reliable start of the combustion engine after a defined parking period from the perspective of the vehicle energy system.
The APM monitors the following data:

 

The result of the calculation can be a shutdown inhibitor or a switch-on request of the MSA.

In the event of engine shutdown, excessive power consumption must be avoided. To ensure this, at terminal 15 On and engine OFF the APM disables all large consumer units or reduces their consumption. The displays remain active.

The following consumer units are affected:

Important! Automatic starting is possible.

If the battery charge state drops after an MSA engine shutdown to below a certain limit, the MSA starts the engine even without any action on the part of the driver.

Note for Service department:

General information

The MSA only works when certain requirements are met (see Operating conditions). In the event of a customer complaint, these requirements must always be checked.

Automatic shut-down at terminal 15 as of 03/2007 in vehicles with automatic engine start-stop function (MSA - optional extra 1CC).

Opening or closing the driver's door (engine OFF) automatically switches off terminal 15 via the signal from the door contact.
By subsequently pressing the START-STOP button, terminal 15 can be switched on again permanently.
Run this operation before programming or diagnosing a vehicle!

Replacement of the zero gear sensor

Replacement of the zero gear sensor may only be carried out according to the instructions in the service function ”learn/write zero gear sensor”. Without correct installation of the sensor, the functionality is inactive or faulty.

Be sure to comply with safety measures for work on vehicles with MSA!

Always ensure that the MSA has been switched off in order to prevent an automatic engine start during work in the engine compartment!

Faults for the MSA

Stored faults for the MSA deactivate the automatic engine start-stop.

MSA and power management

The MSA is strongly networked with the power management. In the event of battery replacement, disconnection of the battery or after programming the engine management system, the reference data regarding the battery charge state and battery condition can be lost.
They are only available again after a closed-circuit current measurement of approx. 6 hours (e.g. closed-circuit current measurement overnight without connected charger) in which the vehicle may not be wakened. In this time, the MSA is inactive.
The customer must be notified of this when the vehicle is handed over. The MSA switches back automatically to active as soon as the necessary routine have been completed successfully.

Diagnosis instructions

The following test modules exist to check the components:

The service function ”read AV memory” can be used to read out a history of the last stored shutdown inhibitors.