WDSBMW wiring diagrams
← Back

Fully automatic convertible top

Fully automatic convertible top

Opening and closing the electrohydraulic convertible top are fully automatic. Opening and/or closing the convertible top takes around 22 seconds. If required, this can also be done when the vehicle is moving at low speed (up to 40 km/h).
Here, the convertible top is moved by hydraulic cylinders. An electric motor unlocks and locks the convertible top at the cowl panel.
After opening, the convertible top is stored in the convertible top compartment. Subsequently, the convertible top cover is closed automatically. The convertible top can be operated using 2 buttons in the centre console switch cluster.

Brief description of components

The following components are described for the fully automatic convertible top:

Sensors for detection of the convertible top position

In total, 8 Hall sensors, 1 micro-switch as well as 1 incremental transducer are installed as sensors for the Convertible Top Module (CTM).

GR_FB5407097

Index

Explanation

Index

Explanation

1

Incremental transducer in the drive for cowl panel locking

2

Hall sensor - lock cowl panel

3

Hall sensor 'main pillar set up'

4

Hall sensor 'main pillar stored'

5

Hall sensor 'tensioning bar extended'

6

Hall sensor 'tensioning bar stored'

7

Hall sensor 'tensioning bar set up'

8

Switch for convertible top compartment floor

9

Hall sensor 'convertible top cover locked'

10

Hall sensor 'convertible top cover locked'

 

Note! No short circuit recognition.

A short circuit of the lead to the switch for the convertible top compartment floor is not detected by the Convertible Top Module (CTM).

CTM: Convertible Top Module

The Convertible Top Module (CTM) controls all the electrical and hydraulic functions of the convertible top. The Convertible Top Module is connected on the K-CAN.

The Convertible Top Module is fitted at the partition wall to the luggage compartment.

Under certain block conditions, the CTM cannot execute a convertible top movement (see 'System functions').

GR_FB5407098

Index

Explanation

Index

Explanation

1

Rollover protection system

2

Convertible Top Module (CVM)

3

Roll bars (extended)

 

 


Button for operation

The centre console switch cluster is equipped with 2 buttons ('open convertible top' and 'close convertible top') for convertible top operation. The centre console switch cluster (SZM) is connected to the heating / air-conditioning control panel (= control module).

GR_FB5407099

Index

Explanation

Index

Explanation

1

'Close convertible top' button

2

'Open convertible top' button

There us a red and green function LED above the two buttons. The control LEDs are activated by the Convertible Top Module (CTM) via the K-CAN.
The green LED lights up during convertible top movement. The red LED starts to flash if the convertible top or convertible top cover is not in a safe end position when the button is released.
The red LED flashing does not indicate a fault. The flashing LED is intended to draw attention to the fact that the vehicle must not be driven in this state.
The red LED lights up when the convertible top is opened by pressing a button and there is a block condition (e.g. convertible top compartment floor not down).

The two control buttons are designed with 2 double contacts (make contact to ground). A direct line leads to the CTM and reports a general operation request. The second line reports the direction to the control module for the heater/air conditioning system (IHR, IHKR, IHKA). Subsequently, the signal is sent via K-CAN to the CTM.
This means that an operation request is executed with a delay. If the button is released during the movement, the convertible top movement or side window movement stops immediately.

Convertible top drive unit

The convertible top drive unit (motor with hydraulic pump and valve block) drives all convertible top movements via 3 cylinder pairs.
One cylinder pair each operates the:

GR_FB5407104

Index

Explanation

Index

Explanation

1

Hydraulic unit

2

Cylinder pair for convertible top cover

3

Cylinder pair for main pillars

4

Cylinder pair for tensioning bar

The direction of movement of the convertible top (OPEN or CLOSED) is controlled by 2 relays.
The cylinders are supplied with oil by a hydraulic pump (3 pistons) with 2 directions of rotation. The reversal of the direction of rotation of the hydraulic pump determines the direction of movement.

The hydraulic pump (max. 200 bar) is installed in the hydraulic unit. The two relays as well as the 3 hydraulic valves for the hydraulic control are also integrated in the hydraulic unit.

The hydraulic unit is secured with a slow-response fuse of 50 Amperes.
A ”pump protection counter” is implemented in the Convertible Top Module (CTM) to protect the hydraulic unit.

The hydraulic pump only operates during the convertible top movement. In the event of failure, emergency actuation is possible.

GR_FB5407100

Index

Explanation

Index

Explanation

1

Frame side member

2

Hydraulic unit
(consisting of hydraulic pump and valve block)

The hydraulic unit is installed in the rear right of the luggage compartment. For acoustic reasons, this is maximum distance away from the driver.

Drive unit for locking cowl panel

An electric motor with transmission locks and unlocks the convertible top with cowl panel at the windshield frame. The Convertible Top Module (CTM) activates the drive.

The drive is arranged in the centre. A rotating disk and thrust rods move the catches to the right and left. The Hall sensor 'cowl panel locked' monitors the interlock.

GR_FB5407101

Index

Explanation

Index

Explanation

1

Drive unit for locking cowl panel

2

Hall sensor - lock cowl panel

3

Thrust rod

4

Catch


The following other control modules are involved in the function of the convertible top:

KOMBI: Instrument cluster

The instrument cluster delivers the outside temperature (bus signal).
The instrument cluster displays via the Check Control messages for the convertible top via Check-Control symbol.

FRM: Footwell Module

The footwell module (FRM) activates the front power windows. To open the convertible top, the side windows must be lowered (bus signal from CTM).

JBE: Junction Box Electronics

The junction box electronics (JBE) actuates the rear power windows. To open the convertible top, the side windows must be lowered (bus signal from CTM).

The junction box electronics deliver the signal as to whether the luggage compartment lid is closed (bus signal).

The distribution box in the junction box supplies the Convertible Top Module (CTM) with terminal 30g.
In addition, the CTM is supplied with terminal 15 by the Car Access System (CAS). If, for example, the power supply from the junction box is interrupted, adequate communication with the BMW diagnosis system is still possible.

CAS: Car Access System

The CAS is the master control module for the power windows.
When requested by the CTM, the CAS ensures that the side windows are lowered and/or raised.
The CAS also prevents opening of the luggage compartment lid and power window movement with the convertible top in its intermediate position.

The Car Access System (CAS) controls convenience opening of the convertible top. The signals from the remote control are received by the FBD receiver and forwarded to the CAS.
Convenience opening and convenience closing via the lock cylinders of the driver's door: The CAS receives the signal from the footwell module (FRM).

System functions

GR_FB5407102

Index

Explanation

Index

Explanation

1

Car Access System (CAS)

2

Footwell module (FRM)

3

Instrument cluster (KOMBI)

4

Center Console Switch Center

5

Heating/air conditioning control module

6

Junction box electronics (JBE)

7

Distribution box in the junction box

8

Rear distribution box

9

Hall sensor 'convertible top cover locked'

10

Hydraulic unit

11

Convertible Top Module (CVM)

12

Switch for convertible top compartment floor

13

Hall sensor - open convertible top compartment lid

14

Hall sensor - lock cowl panel

15

Hall sensor 'tensioning bar extended'

16

Hall sensor 'tensioning bar set up'

17

Hall sensor 'tensioning bar stored'

18

Incremental transducer

19

Drive unit for locking cowl panel

20

Hall sensor 'main pillar set up'

21

Hall sensor 'main pillar stored'

 

 


The following system functions are described for the automatic convertible top:

Opening and closing the convertible top

To open and close the convertible top, the following conditions must be met:

Automatic opening runs as follows:

Note! Bear the national version in mind.

Closing the side windows is encoded on a country-specific basis.

Automatic closing of the convertible top takes place in reverse order.

Convenience operation

The convertible top can be operated using the remote control as well as the mechanical key in the door lock.
In the case of vehicles with optional extra ”Comfort Access”, the convertible top can be opened and closed via the identification sensor.

The convenience functions via the remote control are country-specific.

Conditions for operation with the remote control or identification sensor with Comfort Access (optional extra 322)

 

without optional extra 322 (Comfort Access)

with optional extra 322 (Comfort Access)

EURO and rest of the world

Roof OPEN: possible with remote control

The convertible top cover closes from its own weight. This means the sequence on opening the convertible top differs slightly from operation via the button.

Roof OPEN: even if identification sensor is more than 4 metres away

Roof CLOSED: only if identification sensor is less than 4 metres away

USA/Canada

--- (not encoded)

Roof OPEN: only if identification sensor is less than 4 metres away

Roof CLOSED: only if identification sensor is less than 4 metres away

Check-control messages

In certain situations, it is not possible to open or close the convertible top. Here, the corresponding Check Control messages are displayed in the instrument cluster.
In the case of vehicles with a Central Information Display (CID), a text message and supplementary instructions are displayed.

The Check Control messages provide a better explanation of the red LED on the button, which lights up in the event of a fault.
Any Check Control message that is present is displayed every 5 seconds.

GR_FB5407103

No.

Color

ID

Check Control message

Supplementary information

1

yellow

019

Luggage compartment open!

 

2

yellow

268

Luggage compartment partition!

Luggage compartment partition
No convertible top movement possible.
Place the luggage compartment partition in the required position,
see Owner's Manual.

271

Convertible top!
Reduce speed!

Convertible top
Speed for convertible-top movement exceeded.
Reduce speed and continue convertible top movement.

272

Convertible top!
Emergency operation!

Convertible top
Failure of the convertible top control.
Emergency operation of convertible top,
see Owner's Manual.

559

Convertible top drive unit overheated!

Convertible top operation
Convertible top drive unit overheated

560

No convertible top operation possible!

Convertible top operation
Temporarily no convertible top operation possible.
Causes, see Owner's Manual.

3

red

270

Convertible top not locked!

Convertible top
Automatic locking fault. Lock the convertible top,
see Owner's Manual.
Have the system checked by BMW center.

426

Convertible top control has failed!

Convertible top control has failed!
Convertible top position and interlock cannot be detected.
If convertible top locks safety, you may continue your journey. For information on checking the interlock, see Owner's Manual.

518

Convertible top not locked!

Convertible top
Convertible top not locked. First open or close the convertible top completely, then continue driving.


Notes for Service department

General information

Note! Emergency actuation, see Repair instructions.

The emergency actuation is described in detail in the repair instructions.

Important! There is no anti-trapping mechanism for the rear power windows.

The rear power windows have no anti-trapping mechanism.
This means there is also no one-touch control function for closing the rear windows.

Note! No convenience closing via the outside door handle electronics.

On vehicles with Comfort Access, convenience closing is not possible using the outside door handle electronics. Convenience closing is run via lock cylinders.

Note! Maintenance-free hydraulic fluid.

Because of its life-time oil filling, the hydraulic fluid does not have to be renewed. If the hydraulic fluid has to be topped up due to leakage, only the approved hydraulic fluid may be used. Only add hydraulic fluid up to the mark on the oil reservoir.

Note! If excessive noise is generated, bleed the hydraulic system.

If excessive noise is generated while the hardtop is moving, the hardtop must be opened and closed several times. This will automatically bleed the hydraulic system in the oil reservoir.

Diagnosis instructions

Important! When working on the rollover protection system, open the convertible top.

If the BMW diagnosis system triggers the rollover protection, the convertible top must be opened first of all. Otherwise, the convertible top will be destroyed.
Mechanical triggering is not possible on the E88!

Important! Special feature of the button to open or close the convertible top.

Fault code A69B ”Line release / stop” is stored under the following conditions:

This enables detection of a short circuit to ground on this line.

The fault memory entry can also occur due to incorrect operation: e.g. passenger presses 'open convertible top' and driver switches terminal R On.
In this case, the fault code is stored as ”not present”. The convertible top is temporary without function.
After opening once using the button, the roof is operational again.

Notes on encoding / programming

After replacement, the Convertible Top Module (CTM) must be re-encoded.

Country-specific versions

Bear in mind the different national versions for the convenience functions:
see section ”Convenient operation and convenience function for loading and unloading the luggage compartment”.

No liability can be accepted for printing or other faults. Subject to changes of a technical nature