WDSBMW wiring diagrams
← Back

Tyre Pressure Monitor (RDC)

System function of RDC

The tyre pressure monitor (RDC) is a system for monitoring the tyre pressure when driving. It is offered exclusively in the USA (legal requirement) and as an optional extra in Canada.

The driver sets the tyre pressure to be monitored. He or she instructs the system via the control function in iDrive to save the current tyre pressure as the target pressure value (Reset). The plausibility of the setpoint pressure is checked before the RDC control module adopts it (axle-wise comparison of the target pressures, minimum pressures). A reset is only possible when the air pressure in all wheels is at least 1.6 bar. If the tyre pressure of one wheel falls below this limit, a Check Control message is issued immediately. If the pressure difference between the wheels on one axle > 0.4 bar, the reset is rejected following a plausibility check. A Check Control message is output. Remedy: set tyre pressures to the correct values and then run the reset once again.

Internal sequence after triggered adaptation process (reset):

  1. Recognition of the fitted wheel electronics systems
  2. Identifying of the position of the wheel electronics systems
  3. Plausibility check by checking the target pressures
  4. Adoption of the specified pressures as target pressures

On comparison of the current tyre pressure with the target pressure, the air temperature is taken into account. On the basis of the target pressure and temperature during the reset, the RDC calculates the limit values for the tyre inflation pressure. The tyre inflation pressure increases by 0.1 bar per 10 °C increase in temperature. If the temperature-evaluated values are not reached, the RDC issues a Check Control message.

 

GR_FB3606001

Index

Explanation

Index

Explanation

1

Wheel electronics system, front right

2

RDC transmitter, front right

3

RDC control module

4

Wheel electronics system, rear right

5

RDC transmitter, rear right

6

RDC transmitter, rear left

7

Wheel electronics system, rear left

8

RDC antenna

9

RDC transmitter, front left

10

Wheel electronics system, front left


RDC control module

At the request of the RDC control module, the following messages are queried via the RDC transmitters (125 kHz) by each wheel electronics system:

These messages are then sent across a high-frequency transmission path (433 MHz) to the RDC antenna. The measuring cycle is 54 seconds. The received radio signal are converted into a digital signal in the RDC antenna. This digital signal is forwarded on the bus to the RDC control module.

 

GR_FB3606004

Index

Explanation

Index

Explanation

1

RDC control module

2

Connector for RDC control module


RDC transmitters

The RDC transmitter is a component of the Tyre Pressure Monitor (RDC).
In total, 4 RDC transmitters are installed (front left, front right, rear left and rear right). The 4 RDC transmitters are fitted under the wheel arch trim in the wheelhouses. The 4 RDC transmitters are identical components.

The RDC control module sends a request to the RDC transmitters as a digital signal. Each RDC transmitter has its own electronics as well as its own data line to the RDC control module.
In each RDC transmitter, the digital signal is converted into a radio signal. Subsequently, the RDC transmitters send the request telemetrically to the wheel electronics systems in the wheels.

GR_FB3608002

Index

Explanation

Index

Explanation

1

RDC transmitters

2

4-pin plug-in connection


Structure and inner circuit

All 4 pins at each plug-in connection are used. The outside pins are earth connections. The inner pins are power supply and signal cable. The two earth connection are connected on a board in the electronic module. Only 3 cables are used in the wiring harness.

GR_FB3608004

Index

Explanation

Index

Explanation

1

Transmitter antenna

2

Transmitter

3

Electronic module with electronic evaluation unit

4

Data interface


Diagnosis instructions for RDC transmitters:

If a RDC transmitter fails, the following behaviour is to be expected:


Wheel electronics system

In all wheels, wheel electronics systems are fitted in the wheel drop centre. The wheel electronics systems are bolted onto the filling valves (made of metal).
The wheel electronics systems are identical components.

The RDC control module sends a request to the RDC transmitters across the data line. In each RDC transmitter, the digital signal is converted into a radio signal. Subsequently, the RDC transmitters send the request telemetrically to the wheel electronics systems in the wheels.

For identification by the RDC control module, each wheel electronics system has its own ID (identifier). This ID is transferred with each data interchange.

The information of the acceleration sensor is evaluated for detection of the road wheel. The acceleration sensor is conceived in such a way that the rotation of the wheel is detected as of a certain tangential speed and the corresponding bit is set in the message of the wheel electronics system. In cases of doubt, the bit is used to distinguish between the road wheel and the spare wheel.

GR_FB3608005

Index

Explanation

1

Wheel electronics system

So as not to place an unnecessary load on the state of charge of the battery, the wheel electronics system works in 4 different modes. The mode in which a wheel electronics system runs a measurement or sends a radio signal depends on the tyre pressure and tyre air temperature.

Structure and inner circuit

The wheel electronics system consists of a plastic housing. The plastic housing contains a circuit board and the following components:

GR_FB3608006

Index

Explanation

Index

Explanation

1

Antenna with transmit and receive unit

2

Pressure, temperature and acceleration sensors

3

Battery

4

Electronic evaluation unit


Diagnosis instructions for the wheel electronics systems:

If the wheel electronics system fails, the following behaviour is to be expected:

Note: Deactivating an activated wheel electronics system is not possible.

It is not possible to deactivate a wheel electronics system that has already been activated. However, it does not send a radio signal as long as it has not been activated (trigger signal from RDC transmitter) and the vehicle is at a standstill.

The state of charge as well as the residual runtime of the battery in the wheel electronics system can be shown in the BMW diagnosis system.
The battery of the wheel electronics system cannot be replaced.

RDC antenna

The RDC antenna is a component of the Tyre Pressure Monitor (RDC). The RDC antenna receives the high-frequency radio signals of the 4 wheel electronics systems. The measured values are sent either on request (cyclical, every 54 seconds) or automatically in the event of a breakdown (once per second) by the wheel electronics system.
At temperature values greater than 120 °C within the tyre, the wheel electronics system is switched off; on colling down to below 110 °C, it is switched on again.

The received radio signal are converted into a digital signal in the RDC antenna. This digital signal is forwarded on the bus to the RDC control module.

GR_FB3608001

Index

Explanation

Index

Explanation

1

4-pin plug-in connection

2

RDC antenna


Structure and inner circuit

All 4 pins at each plug-in connection are used. The outside pins are earth connections. The inner pins are power supply and signal cable. The two earth connection are connected on a board in the electronic module. Only 3 cables are used in the wiring harness.

GR_FB3608004

Index

Explanation

Index

Explanation

1

Reception antenna

2

High-frequency receiver

3

Electronic module

4

Data interface


Diagnosis instruction for RDC antenna

If the RDC antenna fails, the following behaviour is to be expected:


Resetting the Tyre Pressure Monitor

On vehicles with iDrive, the RDC is reset via the menu item: Settings/Vehicle/RDC/Reset. In general, the reset can be carried out with the ignition on or engine on (only when vehicle is stationary).

Notes for Service department

Diagnosis instructions

Important! Conditions for reset.

The RDC must be reset in the following cases:

Note! Check of the wheel electronics system

A check as to whether the correct wheel electronics system has been fitted can only by run after the tyre has been removed. Unfortunately, a query via the BMW diagnosis system is not possible for technical reasons.

Note! Reset of the RDC control module

During the reset, the control module functions (measurement data of wheels 1 - 5) contain substitute values until the wheel allocation is complete (e.g. 6.4 bar; 127 °Celsius). To enable successful conclusion of the wheel allocation, the wheels must turn.

National versions

USA, Canada

Transmission frequency of the system: 433 MHz

Reception frequency of the system: 125 MHz

No liability can be accepted for printing or other faults. Subject to changes of a technical nature