Electrochromic interior rear view mirror, digital compass, garage-door opener
Electrochromic interior rear view mirror, digital compass, garage-door opener
The main task of interior rearview mirror is to allow the driver to look through the vehicle from the inside to the rear. The central location in the control panel means the interior rearview mirror is also suitable to accommodate sensors and buttons.
Brief description of components
The following components are described for the interior rearview mirror:
- Interior rear-view mirror
- Junction box electronics (JBE)
Interior rear-view mirror
The central location in the control panel means the interior rearview mirror assumes a number of operating and display functions.
The interior rearview mirror sends its information to the junction box electronics (JBE) via a LIN bus.
Junction box electronics (JBE)
The JBE control module receives the information from the interior rearview mirror via the LIN bus and also makes the information to other control modules via the K-CAN. D.

Sample illustration, interior rearview mirror
Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Interior rearview mirror glass (electrochromic) |
2 |
Photo diode for automatic anti-glare control (electrochromic) |
3 |
LED for the anti-theft alarm system (DWA) |
4 |
Buttons for the garage-door opener |
System functions
Depending on the equipment specification, various system functions are available for the interior rearview mirror. The following system functions are described:
- Electrochromic
- Garage-door remote controls
- Digital compass
Electrochromic
The electrochromic interior rearview mirror automatically dims the mirror glass if a source of light from the rear is detected. The electrochromic interior rearview mirror has two sensors that measure light incidence from the front and the rear. When the light source from the rear is strength, a voltage signal is output. The strength of the voltage signal depends on the light difference between the front and rear. The greater the voltage signal, the more the mirror glass is dimmed. The electrochromic interior rearview mirror controls the electrochromic outside mirrors via the junction box electronics (JBE).
Garage-door remote controls
The garage-door opener replaces up to three different hand-held transmitters. This integrated universal remote control can learn various radio-remote-controlled facilities, e.g. garage doors and garden gates or lighting systems. The integrated universal remote control detects and learns the sent signal from each original hand transmitter.
The frequency of the transmitter must be set for the relevant country (see Owner's Handbook). The following country settings are distinguished:
- USA
- France
- Italy
- UK (Great Britain and Northern Ireland)
- Rest of Europe
Digital compass
The compass offers an additional benefit especially in the USA. In large cities, the streets are frequently arranged according to the points of the compass. The signposts are also specified with points of the compass.
However, the compass also assists orientation in large European cities on the basis of the points of the compass.
The magnetic field sensor is on the PCB in the interior rearview mirror. The magnetic field sensor measures the current alignment of the magnetic field.
The control electronics for the compass are integrated into the board for the interior rearview mirror. The signals from the magnetic field sensor are received by the control electronics. The LCD display is activated directly by the control electronics.
The following system functions for the digital compass are described:
- Display
Each point of the compass is displayed in transparent light technology in the interior rearview mirror. The display is in the top right of the interior rearview mirror. The display is divided into eight compass points. The display is available in English and German (delivery status: English in left-hand drive).
N: North
NE: North East (German: NO)
E: East (German: O)
SE: South East (German: SO)
S: South
SW: South West
W: West
NW: North West
The changeover between displays is carried out as follows:- The current vehicle position is the centre of a 360° circle.
- The eight points of the compass divide these 360° into sixteen 22.5° segments.
- The display changes over if the direction of travel changes by more than 22.5°.
- The current vehicle position is the centre of a 360° circle.
- Brightness control of display
2 photocells in the electrochromic interior rearview mirror record the surrounding brightness (1 photocell for the surrounding brightness coming from the front, 1 photocell for the surrounding brightness coming from the rear). The photocells deliver the signals for the display brightness control. The brightness of the display is adjusted by the interior rearview mirror control electronics to suit the surrounding brightness. - Adjustment of magnetic field zones and calibration
The worldwide magnetic field zones are permanently stored in the interior rearview mirror. The magnetic field zones represent the deviations in relation to an ideal magnetic field for earth. The orientation ”North” is precisely determined by the magnetic field zones. The current magnetic field zone may be adjusted according to the geographic location. For example, Germany is located in magnetic field zone ”8”.
A vehicle has its own magnetic field. This makes it possible for the magnetic field sensor to measure an overlapping of the magnetic field with the earth's magnetic field. This overlapping is ”worked out” by calibrating the compass.
A changed magnetic field is normally calibrated ”automatically”. The vehicle's magnetic field may change under the following special circumstances:- Powerful vibration during an accident
- Very large external magnetic field - e.g. if a vehicle passes under a train when travelling through an underpass
- Powerful vibration during an accident
No liability can be accepted for printing or other faults. Subject to changes of a technical nature