Rear ventilation grille
Rear ventilation grille
The design of the rear ventilation grille depends on the climate control that is installed.
- Automatic climate control in basic version (IHKA Basic) without left-right separation in the rear
The following electrical components are installed in the rear ventilation grille:- LED for locating light
- Rear stratification control
The rear stratifying-flap motor controlled the stratification for the rear-compartment ventilation. - LED for locating light
- Automatic climate control with high equipment (IHKA High) with rear automatic climate control (FKA) and left-right separation in the rear
The following electrical components are installed in the rear ventilation grille:- LED for locating light
- Ventilation temperature sensor, rear left
- Ventilation temperature sensor, rear right
- Rear-left stratification control
- Rear-right stratification control
In the FKA control module, the signals are evaluated, digitized and sent across the CAN bus to the IHKA control module. The IHKA control module evaluates this information and activates the rear stratifying-flap motors on the right and left. This regulates the stratification for the rear-compartment ventilation separately for the left and right. - LED for locating light
Functional description
The rear ventilation temperature sensors are hot conductors or NTC resistors (”NTC” stands for ”Negative Temperature Coefficient”).
The hot conductor means that the variable ”temperature” can be converted into the variable ”resistance” which can be electrically evaluated. The current-conducting materials in the hot conductor conduct current better at high temperatures than at low temperatures. That means: With rising temperatures, the resistance falls.
The rear stratification controls have a linear resistance value dependent on the angle of rotation.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Rear ventilation grille (back) |
2 |
Rear-left ventilation temperature sensor |
3 |
Rear-left stratification control |
4 |
Rear-right stratification control |
5 |
Rear-right ventilation temperature sensor |
|
|
Structure and inner circuit
The locating light in the rear ventilation grille is controlled by the footwell module (FRM).
Rear ventilation grille without left-right separation in the rear
The junction box electronics (JBE) supply the rear ventilation grille with voltage and ground.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Locating light (LED) |
2 |
Rear stratification control |
Pin assignments
Pin |
Explanation |
|---|---|
Kl. 58g |
Terminal 58g, locating light |
Kl. 31L |
Terminal 31, load ground |
5 Volts |
Power supply |
SIG |
Rear stratification control signal line |
Rear ventilation grille with rear automatic climate control and left-right separation in the rear
The rear ventilation temperature sensors and rear stratification controls are supplied with voltage by the FKA control module. In order to balance out internal temperature effects, the hot conductor is operated with low current. This means that the outer ambient temperature is decisive for the resistance value.
Each temperature change on the hot conductor leads to a change in the voltage signal. The signals from the 2 rear ventilation temperature sensors are sent separately across signal lines to the FKA control module.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Ventilation temperature sensor, rear left |
2 |
Rear-left stratification control |
3 |
Locating light (LED) |
4 |
Rear-right stratification control |
5 |
Ventilation temperature sensor, rear right |
|
|
Pin assignments
Pin |
Explanation |
|---|---|
Kl. 58g |
Terminal 58g, locating light |
Kl. 31L |
Terminal 31, load ground |
5 Volts |
Power supply |
SIG1 |
Rear-left stratification control signal line |
SIG2 |
Rear-right stratification control signal line |
SIG3 |
Signal line and supply line for rear-left ventilation temperature sensor |
SIG4 |
Signal line and supply line for rear-right ventilation temperature sensor |
Characteristic curve and target values
Rear compartment ventilation temperature sensor
Each change to the rear ventilation temperature sensor leads to a change in the resistance signal.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Temperature in degrees Celsius (°C) |
2 |
Characteristic curve for hot conductor |
3 |
Resistance in Kiloohms (k) |
|
|
Observe the following target values for the right or left ventilation temperature sensor:
Variable |
Value |
|---|---|
Power supply |
5 V |
Temperature range |
-40 to 85 °C |
Resistance range (measuring range) |
1.2 to 100 k |
Rear stratification control
Each manual change to the rear stratification control leads to a change in the resistance signal. The evaluation takes place in the IHKA control module. The value is registered as a percentage (%).

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Voltage characteristics in Volts (V) |
2 |
Characteristic curve for rear stratification control |
3 |
Adjusting path of the rear stratification control as a percentage (%) |
|
|
Observe the following target values for the rear right and rear left stratification controls:
Variable |
Value |
|---|---|
Power supply |
5 V |
Range of rotation |
approx. 60° |
Voltage in end position, fresh air |
1.5 ± 0.1 V |
Value in end position, fresh air as a percentage |
0 + 5 % or 0 % |
Voltage in end position, warm air |
3.4 ± 0.1 V |
Value in end position, warm air as a percentage |
100 + 0 % or - 5 % |
Temperature range |
-40 to 85 °C |
Diagnosis instructions
Failure of the component:
Rear compartment ventilation temperature sensor
If the rear ventilation temperature sensor fails, the following behaviour is to be expected:
- Fault memory entry in the FKA control module
- Substitute value from the IHKA control module: 20 °C
Rear stratification control in the IHKA Basic
If the rear stratification control fails, the following behaviour is to be expected:
- Fault memory entry in the junction box electronics (JBE)
- Substitute value from the IHKA control module for the rear stratifying-flap motor: 50 %
Rear stratification control in the IHKA High with rear automatic climate control
If a rear stratification control fails, the following behaviour is to be expected:
- Fault memory entry in the FKA control module
- Substitute value from the IHKA control module: 50 %
No liability can be accepted for printing or other faults. Subject to changes of a technical nature