Crankshaft sensor
Crankshaft sensor
The crankshaft sensor is attached to the transmission case.
The crankshaft sensor picks up the position of the crankshaft by means of a sensor wheel bolted onto the disk flywheel. The engine management system uses this to calculate the engine speed. The crankshaft sensor and camshaft sensor are necessary for the fully sequential injection system (fuel injection takes place individually for each cylinder at the specific point of ignition).
The signal from the crankshaft sensor means that the engine management system also evaluates the crankshaft acceleration. The crankshaft acceleration provides an indication of the combustion quality of individual cylinders.
Functional description
The sensor wheel (= multi-pole sensor wheel) has 58 magnetic pole pairs as well as a reference point. The reference point of the multi-pole sensor wheel is shown by a pole pair that is twice as long.
The reference point enables detection of the upper dead centre of the 1st cylinder. By monitoring the individual pairs of poles, the Hall sensor delivers a certain number of signal jumps to the engine management system.
The active crankshaft sensor detects the direction of rotation of the crankshaft as well as the air gap in relation to the sensor wheel.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Crankshaft sensor |
2 |
Sensor wheel (multi-pole sensor wheel) |
3 |
3-pin plug-in connection |
|
|
The engine control module uses the scanned signals to calculate the duration as well as the length of a crankshaft revolution.
The time the sensor wheel requires to rotate past the Hall sensor is referred to as the crankshaft revolution per time.
For starting the engine, the engine control module checks the following conditions:
- fault-free signal from the crankshaft sensor and camshaft sensor
- both signals must be detected in a specific chronological sequence
This process is referred to as synchronization and is only performed when the engine is started. The synchronization enables the engine control module to activate the fuel injection correctly.
Without synchronization, no engine start is possible.
If the crankshaft sensor signals fails (with the 1st crankshaft revolution) or an invalid synchronization is detected for the engine start, the diagnosis starts immediately. The camshaft sensor signals are read here. If 12 flanks on the camshaft are read and the fault is still there, a fault is stored.
As soon as no crankshaft sensor signals are received or there is no valid synchronization with the engine running, debouncing starts.
Structure and inner circuit
The sensor contains 3 Hall elements fitted side by side in one housing. The signals of the first and 3rd Hal elements form the differential signal to determine the signal frequency and air gap to the multi-pole sensor wheel. The temporal offset of the signal of the middle element to the differential signal allows detection of rotation to the right or left.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Sensor wheel |
2 |
Hall sensors |
3 |
Electronic evaluation unit |
|
|
Pin assignments
Pin |
Explanation |
|---|---|
5 V |
5 Volts, power supply |
SIG |
Signal line |
Kl. 31 |
Terminal 31, ground |
Characteristic curve and target values
The transition from a high to a low phase is signalled by a change in the magnetic field. These changes are counted in the engine management system. The difference between 2 changes of the magnetic field is 6° crankshaft angle.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Signal path (calculated internally) |
2 |
Sensor wheel |
3 |
Reference signal |
|
|
Observe the following target values for the crankshaft sensor:
Variable |
Value |
|---|---|
Voltage range |
4.5 to 5.5 V |
Signal voltage |
4.1 to 5.1 V |
Engine speed range |
up to 8000 rpm |
Air gap range |
0.1 to 1.8 mm |
Maximum current consumption |
25 mA |
Outside temperature |
-40 °C to 160 °C |
Diagnosis instructions
Failure of the component
If the crankshaft sensor fails, the following behaviour is to be expected:
- Fault memory entry in the engine control module
- Emergency operation with substitute value
No liability can be accepted for printing or other faults. Subject to changes of a technical nature