Exhaust camshaft sensor
Exhaust camshaft sensor
The exhaust camshaft sensor is attached to the cylinder head cover.
The exhaust camshaft sensor detects the position of the exhaust camshaft with the help of an increment gear attached to the camshaft (camshaft sensor wheel).
The exhaust camshaft sensor is required for the information signal for adjustment of the exhaust camshaft (VANOS).
Functional description
To perform the adjustment, the variable camshaft control requires an information signal on the current position of the camshaft. Camshaft sensors on the intake and exhaust end record the position of the camshafts.
The exhaust camshaft sensor is designed as a non-contact Hall sensor.
The camshaft sensor wheel has 6 different flank spacings. The flank spacings are detected by the Hall sensor.
The engine management system uses these to calculate:
- Camshaft rotational speed
- Camshaft speed
- Exact position of the camshaft

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Cylinder head cover |
2 |
Exhaust camshaft sensor |
3 |
3-pin plug-in connection |
|
|
A controlled VANOS adjustment unit is fitted at both intake and exhaust camshafts. A VANOS solenoid valve activates the VANOS adjustment unit. The required positions of the intake and exhaust camshafts are calculated from the engine speed and the load signal (depending on the intake-air temperature and engine temperature). The DME control module activates the VANOS adjustment unit accordingly. The control of the intake and exhaust camshaft is variable within their maximum adjustment range.
When voltage is applied, it is detected whether the sensor is above a tooth or above a gap.
Structure and inner circuit
The measurement procedure is based on Hall IC. The output signal has the status Low above a flank and the status High above a gap.
The exhaust camshaft sensor works according to the same principle as the crankshaft sensor. However, the camshaft sensor wheel differs fundamentally. A special mark pattern enables emergency operation in the event of failure of the crankshaft sensor. However, the resolution of the camshaft sensor signal is too imprecise to replace the crankshaft sensor during normal operation.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Camshaft sensor wheel |
2 |
Hall-effect sensor |
3 |
Electronic evaluation unit |
|
|
Pin assignments
Pin |
Explanation |
|---|---|
Kl. 15N |
Terminal 15N, power supply |
Kl. 31 |
Terminal 31, ground |
SIG |
Signal line |
Signal path and target values
The engine control module reads in the sensor signal and compares the signal with a stored pattern.
The calibration between the sensor signal and stored pattern means that the exact position of the camshaft or the deviation is detected.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Intake camshaft |
2 |
Exhaust camshaft |
3 |
Intake camshaft signal |
4 |
Exhaust camshaft signal |
5 |
Reference mark for top dead centre, cylinder 1 (ignition) |
6 |
Cylinder |
Observe the following target values for the camshaft sensor:
Variable |
Value |
|---|---|
Voltage range |
6 to 16 Volts |
Maximum operating current |
Less than 15 A |
Engine speed range |
0 to |
Air gap range |
0.4 to 2.0 mm |
Maximum output current |
20 mA |
Temperature range |
-40 °C to 160 °C |
Diagnosis instructions
Failure of the component:
If the exhaust camshaft sensor fails, the following behaviour is to be expected:
- Fault memory entry in the engine control module
- Emergency operation with substitute value
General information
The diagnosis for the exhaust camshaft sensor starts under the following conditions:
- DME main relay ON
- Engine running
- Engine is synchronized
- No stalling of the engine detected
- Error-free signal from the crankshaft sensor
No liability can be accepted for printing or other faults. Subject to changes of a technical nature