Slide/tilt sunroof drive unit
Slide/tilt sunroof drive unit
The slide/tilt sunroof drive is installed near the roof function centre from below on the frame for the slide/tilt sunroof.
The drive for the slide/tilt sunroof consists of an electric motor with reduction gears.
The switch for the slide/tilt sunroof is located in the roof function centre (FZD). The function of the slide/tilt sunroof control module has also been integrated into the FZD control module.
The sliding panel and wind deflector are driven by the sliding panel drive.
Functional description
If the FZD control module receives a request for the slide/tilt sunroof, it activates the electric motor. The electric motor is supplied with voltage (terminal 30) via a relay integrated in the roof function centre.
There are 2 integrated Hall sensors in the electric motor of the slide/tilt sunroof. The Hall sensors pick up the motor revolutions. The Hall-sensor signals are forwarded to the FZD control module.
The Hall-sensor signals enable the FZD control module to detect the position of the slide/tilt sunroof. In addition, the closing speed of the slide/tilt sunroof is used to calculate the closing power in the control module.
The mechanical forces change with ambient temperature and ageing. Consequently, the required closing force and anti-trap function are adjusted each time the sunroof closes.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Slide/tilt sunroof drive unit |
2 |
6-pin plug-in connection |
3 |
Reduction gear |
4 |
Electric motor |
Safety functions:
- Maximum motor run time
If the motor run time for one direction is longer than 15 seconds, the FZD control module switches off the slide/tilt sunroof drive. - Overheating protection
Heating of the electric motor is calculated continuously on the basis of the measured ambient temperature as well as the operating period by means of a thermal model in the FZD control module.
The available temperature signal is the outside temperature (via K-CAN). There is also a temperature sensor on the circuit board of the FZD control module. As of a certain temperature threshold, the FZD control module switches off the slide/tilt sunroof drive. - Blocking protection
If the Hall impulses from the electric motor fail to arrive for longer than 500 milliseconds, the FZD control module switches off the slide/tilt sunroof drive.
Structure and inner circuit
The slide/tilt sunroof drive is connected to the FZD control module by means of a 6-pin plug-in connection.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Electric motor |
2 |
Hall sensors |
Pin assignments
Pin |
Explanation |
|---|---|
SIG1 |
Terminal 30 (power supply) or terminal 31L (load earth), depending on the activation (open or close) |
SIG2 |
Terminal 30 (power supply) or terminal 31L (load earth), depending on the activation (open or close) |
SIG3 |
Signal from Hall sensor 2 |
SIG4 |
Earth connection for the Hall sensors (via FZD control module) |
SIG5 |
Signal from Hall sensor 1 |
1 pin not used. |
|
Target values
Comply with the following target values for the slide/tilt sunroof drive:
Variable |
Value |
|---|---|
Power supply |
9 to 16 V |
Maximum current consumption |
10 ± 0.2 A |
Maximum short-term (1 second) current consumption with blocking |
26 A |
Temperature range |
-40 to 80 °C |
Diagnosis instructions
Failure of the component
If the slide/tilt sunroof drive fails, the following behaviour is to be expected:
- Fault memory entry in the FZD control module
- Check Control message via symbol in the instrument cluster (KOMBI)
- Slide/tilt sunroof drive and sliding panel drive inoperative, i.e.: the slide/tilt sunroof and sliding panel remain in their current positions.
No liability can be accepted for printing or other faults. Subject to changes of a technical nature