Lumbar support active seat drive, driver or passenger
Lumbar support active seat drive, driver or passenger
The lumbar support active seat drive supplies the air cushions in the active seat as well as the lumbar cushions with compressed air.
Functional description
The driver seat module (SMFA) and/or passenger seat module (SMBF) controls the lumbar support active seat drive for the driver and/or passenger.
The lumbar support active seat drive contains the following components:
- Pneumatic pump with pump motor
The pneumatic pump generates the compressed air for the air cushions and lumbar cushions.
The pneumatic pump is driven by the pump motor (DC motor). - Solenoid valve
The solenoid valve forwards the air flow from the pneumatic pump as follows:- to the lumbar cushions
or - to the pressure distributor for the air cushions of the active seat
- to the lumbar cushions
- Pressure relief valve
The pressure relief valve protects the system against excessive system pressure. The pressure relief valve is fitted after the pneumatic pump in the supply line. - Control electronics
The control electronics have the following functions:- Activation of the pump motor
The control electronics only activate the pump motor to inflate the 4 air cushions of the active seat and the lumbar cushions.
The control electronics control 2 power stages on the pump motor:- Active seat function selected:
the pump motor runs with reduced power output. - Lumbar support function selected:
the pump motor runs at full power output.
- Active seat function selected:
- Activation of the solenoid valve
According to the selected function (active seat or lumbar support), the control electronics switch the solenoid valve. The air flow is directed to the downstream components.
- Activation of the pump motor

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Connection to valve block for lumbar support, driver and/or passenger |
2 |
3-pin plug-in connection |
3 |
Housing to accommodate the solenoid valve |
4 |
Connection to the pressure distributor for active seat, driver and/or passenger |
5 |
Housing with insulation to accommodate the pneumatic pump and the pump motor |
6 |
Housing to accommodate the pressure relief valve |
7 |
Housing to accommodate the non-return valve |
|
|
Structure and inner circuit
The lumbar support active seat drive for the driver and/or passenger is connected by means of a 3-pin plug connection to the driver seat module (SMFA) and/or passenger seat module (SMBF).

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Control electronics |
2 |
Pump motor |
3 |
Solenoid valve |
|
|
Pin assignments
Pin |
Explanation |
|---|---|
U |
Power supply via seat module |
SIG |
Activation of solenoid valve |
Terminal 31L |
Terminal 31, load ground |
Pneumatic system
The operating pressure fluctuates between 0.34 and 0.5 bar.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Lumbar support active seat drive, driver or passenger |
2 |
Solenoid valve |
3 |
Pressure relief valve |
4 |
Pneumatic pump with pump motor |
5 |
Non-return valve |
6 |
to the pressure distributor for active seat, driver and/or passenger |
7 |
to the valve block for lumbar support, driver and/or passenger |
|
|
Target values
Comply with the following target values for the lumbar support active seat drive for the driver and/or passenger:
Variable |
Value |
|---|---|
Voltage range |
9 to 16 V |
Rated current (solenoid valve) at 13 V |
350 mA |
Rated current (pump motor) at 13 V |
400 mA |
Temperature range |
-40 to 85 °C |
Diagnosis instructions
Failure of the component
If the lumbar support active seat drive for the driver and/or passenger fails, the following behaviour is to be expected:
- Fault memory entry in the driver seat module (SMFA) or passenger seat module (SMBF)
No liability can be accepted for printing or other faults. Subject to changes of a technical nature