Rear compartment flap motor
Rear compartment flap motor
The rear compartment flap motor is the drive for 2 stratification and 2 ventilation flaps in the rear ventilation duct without left-right separation.
The left-hand stratification flap and the right-hand stratification flap are firmly mounted on a joint shaft.
The stratification flap is used to adjust the air stratification. That means: The proportions of cold and warm air in the air flow towards the rear right-hand ventilation air vents are altered in relation to one another.
In the same way as the stratification flaps, the left-hand and right-hand ventilation flaps are firmly mounted on a joint shaft.
The ventilation flap is used to regulate the air supply into the rear.
The two shafts are connected by means of a cam disk to the rear compartment flap motor.
The drive consists essentially of the following parts:
- Rear compartment flap motor (actuator drive)
- Electronic module (with integrated circuit)
- Transmission
- Housing
Functional description
The control module of the rear automatic climate control (FKA control module) evaluates the signal from the rear stratification control. The signal is sent as a message on the CAN bus. The control module of the integrated automatic heating / air-conditioning system (IHKA control module) evaluates this message and activates the rear compartment flap motor across the LIN bus.
The rear compartment flap motor is fitted with an integrated circuit. This circuit controls the coil of the rear compartment flap motor. The circuit is bus- and diagnosis-compatible.
After activation of the rear compartment flap motor, the integrated circuit sends a position message (actual position) to the IHKA control module.
After the vehicle is stopped and parked and after a specified waiting period (stored in the memory chip of the IHKA control module), the rear compartment flap motor is moved to a certain parking position. The rear compartment flap motor is re-initialized to this parking position after starting up.
- Shutdown in the event of blocking
The integrated circuit detects blocking of the rear compartment flap motor in that there is increased current consumption within the adjustment range. The integrated circuit reports the fault across the LIN bus to the IHKA control module. The IHKA control module no longer activates the defective rear compartment flap motor.
If the blocking occurs outside of the adjustment range, an end stop is detected correctly. - Reference run
The rear compartment flap motor is unable to detect the current position (actual position). The rear compartment flap motor always moves relative to an end position of the stratification flaps or ventilation flaps (reference point). One of the end positions of the stratification flaps or ventilation flaps (closed or fully opened) serves as the reference point.
After replacement of the IHKA control module as well as after an interruption to the power supply, the stratification flap or ventilation flap is moved to an end position.
The end position is selected in such a way that the subsequent nominal position can be reached by the shortest route.
The reference run can also be initiated by the BMW diagnosis system.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
4-pin plug-in connection |
2 |
Rear compartment flap motor |
3 |
Gearbox output |
|
|
Structure and inner circuit
The rear compartment flap motor is connected to the IHKA control module by means of a 4-pin plug-in connection.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Electronic module |
2 |
Rear compartment flap motor |
Pin assignments
Pin |
Explanation |
|---|---|
Terminal 31L |
Terminal 31, load ground |
LIN in |
LIN bus input |
LIN out |
LIN bus output |
U |
Power supply |
Target values
Comply with the following target values for the rear compartment flap motor:
Variable |
Value |
|---|---|
Power supply |
12 V |
Voltage range |
8 to 16 V |
Temperature range |
-40 ± 85 °C |
Diagnosis instructions
The flap motors communicate across the LIN bus with the IHKA control module. The flap motors are switched in series on the LIN bus.
The flap motors in the integrated automatic heating / air-conditioning system (IHKA) are all the same. During operation, the only difference between them is their programmed address.
Each flap motor is assigned a certain address. The address determines what function the flap motor assumes in the composite system. This address tells e.g. the rear compartment flap motor that messages are being addressed to it (e.g. 'open flap'). This address also tells e.g. the IHKA control module which flap motor has sent it a fault message.
A precondition for successful addressing of the flap motors is correct coding of the IHKA control module.
After starting the auto-addressing, an address is programmed into the flap motor that is topologically last in the series connection. Then an address is programmed into the topologically second-last flap motor etc. until all the addresses have been assigned. This means that the installation location of the flap motor in the wiring harness decides which address is programmed into the flap motor.
If e.g. during auto-addressing the topologically last flap motor is not connected to the wiring harness of the IHKA control module or there is no connection via the LIN bus, the topologically second-last flap motor is erroneously detected as the topologically last flap motor. This means that the wrong address is written into this flap motor. The remaining stepper motors are also given an incorrect address.
Confusing connectors also leads to incorrect addressing.
If a number of flap motors are entered in the fault memory with the fault ”not responding”, there is probably a break in the connection via the LIN bus.
The search for the break (cable, connector, flap motor) must then start at the topologically first of the entered flap motors.
Failure of the component:
If the rear compartment flap motor fails, the following behaviour is to be expected:
- Fault memory entry in the IHKA control module
- Emergency operation: If a fault occurs, e.g. no bus communication over a certain period of time, emergency operation starts.
During emergency operation, the rear right stratification-flap motor is no longer activated. This means that the stratification flap remains in its current position.
No liability can be accepted for printing or other faults. Subject to changes of a technical nature