Pressure distributor for active seat, driver and/or passenger
Pressure distributor for active seat, driver and/or passenger
The pressure distributor distributes the air flow generated by the pneumatic pump to the 4 air cushions in the active seat. Two air cushions are arranged one above the other on the left-hand and right-hand seat cushions.
The pressure distributor automatically regulates the inflation and deflation of the air cushions.
Functional description
The pressure distributor in the active seat for the driver and/or passenger consists of the following components:
- Drive mechanism
The drive unit consists of the electric motor and a transmission.
If the active seat function is activated, the electric motor permanently drives the unit for pressure distribution.
- Micro-switch to switch the pump motor on and off
The micro-switch is directly connected to the driver seat module (SMFA) and/or passenger seat module (SMBF). The micro-switch probes a signal disk with 4 cams in the drive unit (4 cams for the inflation and deflation of individual air cushions). This picks up the work cycle. One revolution of the drive mechanism is a work cycle and it lasts approx. 80 seconds.
To deflate the air cushions, only the pump motor of the pneumatic pump is switched off. The drive unit in the pressure distributor continues to run.
- Unit for pressure distribution
The unit for pressure distribution distributes the air flow to the 4 air cushions. A camshaft activates slide valves that enable inflation, pressure-holding and deflation of the air cushions.
The pressure distributor in the active seat for the driver or passenger can be switched on as of terminal 15 On. The driver seat module (SMFA) and/or passenger seat module (SMBF) activates the pressure distributor in the active seat for the driver and/or passenger.
If the system is switched off via the active seat button, the 4 air cushions must be deflated.
Deflating: That means: If the pneumatic pump is switched off, the pressure distributor runs a complete work cycle.
After a timeout of more than 100 seconds, the power supply is interrupted automatically by the driver seat module (SMFA) and/or passenger seat module (SMBF).
If the system is not fully deflated after disconnecting the battery or resetting the seat module, activation takes place. The signal is sent by the micro-switch in the pressure distributor. If the pneumatic pump is switched off, the pressure distributor runs a complete work cycle.
After a timeout of more than 100 seconds, the power supply is interrupted automatically by the seat module.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Pressure distributor for active seat, driver and/or passenger |
2 |
Camshaft |
3 |
Connections for the air ducts to the air cushions |
4 |
Connection for supply with compressed air from the pneumatic pump |
5 |
Signal disk |
6 |
Transmission |
7 |
Electric motor |
8 |
Micro-switch |
If the driving speed and lateral acceleration are above a defined value for approx. 0.25 seconds, the active seat function is disabled. The function indicator remains switched on. If the value is again undershot for approx. 3 seconds, the system resumes the function at the stopped position.
Structure and inner circuit
The pressure distributor in the active seat for the driver and/or passenger is connected to the driver seat module (SMFA) and/or passenger seat module (SMBF).

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Drive motor |
2 |
Micro-switch |
Pin assignments
Pin |
Explanation |
|---|---|
Terminal 31L |
Terminal 31, load ground |
U |
Power supply via seat module |
SIG |
Signal line (signal from micro-switch) |
1 pin not used. |
|
Target values
Observe the following target values for the pressure distributor in the active seat, driver:
Variable |
Value |
|---|---|
Voltage range |
9 to 16 V |
Rated current |
70 mA |
Maximum current consumption (< 1 minute) |
1 A |
Temperature range |
-40 to 85 °C |
Diagnosis instructions
Failure of the component
If the pressure distributor for the active seat for the driver and/or passenger fails, the following behaviour is to be expected:
- Fault memory entry in the driver seat module (SMFA) or passenger seat module (SMBF)
No liability can be accepted for printing or other faults. Subject to changes of a technical nature