Injectors
Injectors
The Common Rail System of the 3rd generation has Piezo injectors. The fuel pressure is approximately 1800 bar. A Piezo element moves a hydraulic coupler as well as a shifting travel valve in the Piezo injector (not a solenoid coil). The Piezo-electrical activation has the following advantages:
- Rapid movement of the nozzle needle due above all to the reduction in mass by approx. 75 %
- Rapid switching times with a very short dead time
- Better metering of multiple fuel injections
- More exact stroke of the nozzle needles
- Lower electrical power consumption, as no holding current is necessary
This results in significant improvements with regard to pollutant emissions and acoustics.
When closed, Piezo injectors do not leak (in contrast to solenoid valve injectors). Due to the way Piezo injectors are designed and how they function, the return volume is significantly lower in comparison with solenoid valve injectors. The return line is connected hydraulically with the pre-delivery system. This is why the pre-delivery pressure is applied in the return line.
Functional description
The Piezo injector enables multiple fuel injection with a maximum of 4 injection operations. This multiple fuel injection can be composed of:
- Pre-injection(s)
- Main injection
- Post injection(s)
The pre-injection improves the acoustic pattern due to softer combustion. At idle speed and up to approx. 2000 rpm, double pre-injection is possible. Post injection is used for regeneration of the diesel particle filter. At low load and engine speed, double post injection is possible.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Injectors |
2 |
Return line |
3 |
High-pressure pipe |
4 |
2-pin plug-in connection |
The volume of fuel required for the operating situation is injected by an injector into the combustion chamber. This volume can be influenced with three adjusting values:
- Rail pressure
- Injector nozzle opening duration
- Injector opening stroke
The nozzle opening duration and opening stroke are specified by the engine management system. The nozzle opening duration is controlled via the fuel injection signal (Ti signal). The opening stroke is controlled via the amount of energy in activation of the injector.
Structure and inner circuit
A piezo element is an electromechanical converter. The piezo element is a type of ceramic that converts electrical energy directly into mechanical energy (power/travel). The piezo element expands when voltage is applied. This creates the lift of the nozzle needle. To achieve a greater lift, a piezo element can be structured in a number of layers.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
Injectors |
|
|
Pin assignments
Pin |
Explanation |
|---|---|
160 V |
Injector power supply (transformed upwards) |
Kl. 31E |
Electronics ground, injector activation |
Activation and target values
The engine management system is supplied with vehicle voltage. The engine management system contains a DC/DC converter across which the voltage is transformed upwards for activation of the injector.
The lines of the positive side are bridged in the DDE control module. Each injector is connected to the DDE control module by means of its own pin and line.
Note! Failure of all injectors.
If a fault occurs on the positive side, the fact that the wires are combined means that the cause of the fault may originate from any of the wires. In such cases, all injectors of the cylinder bank concerned will fail.

Index |
Explanation |
Index |
Explanation |
|---|---|---|---|
1 |
High voltage |
2 |
Injection signal |
3 |
Time |
4 |
Fuel injection period |
Observe the following target values for the injector:
Variable |
Value |
|---|---|
Maximum power supply |
approx. 160 volts |
System pressure |
200 to 1800 bar |
Nozzle opening duration, nozzle closing duration |
100 to 200 s |
Dynamic throughflow at 0.4 ms |
14.5 mg/stroke |
Temperature range |
-30 °C to 140 °C |
Diagnosis instructions
Failure of the component
If an injector fails, the following behaviour is to be expected:
- Fault memory entry in the engine control module
- If more than 1 injector fails, it is not possible to continue driving
No liability can be accepted for printing or other faults. Subject to changes of a technical nature
General information
If one or more injectors is replaced, the injector volume compensation must be executed, see corresponding service function on the BMW diagnosis system.
It is currently not possible to measure the return volume for Piezo injectors. Due to the way Piezo injectors are designed and how they function, the return volume is considerably lower than in the case of solenoid valve injectors.
Note! Observe the pre-delivery pressure.
On engine with Piezo injectors, the pre-delivery pressure is applied in the fuel return flow! This configuration is necessary for operation of the Piezo injectors.
No liability can be accepted for printing or other faults. Subject to changes of a technical nature